May 2022
Product & Price List
Products
Console Enhancements
We stock a range of cosmetic items suitable for all ages and ranges of Neve consoles.
From: P.O.A
Eurocards
This card allows high quality buffering of balanced signals whilst cutting or boosting the level of each signal.
From: P.O.A
This is an equivalent to the Neve EV11694 Legend Mix Amp - not a substitute as the differences in sound and specification are not enough to warrant a replacement.
From: £395.00
Stereo Headphone Amplifier with connections for external balance and level controls and a power regulator. Fitted to a Eurocard size PCB to allow for fitting in custom racks.
From: P.O.A
A 13-input stereo balanced switching matrix that any number of balanced stereo inputs can be selected making the card suitable for source selection in a monitor matrix or routing within a mixing console.
From: P.O.A
A general purpose relay card featuring 12 double-pole change-over relays with all switch contacts available for use.
From: P.O.A
Fully compatible with the Neve EV11319/B relay card used in the V / VR consoles. With additional control lines to switch all relays on or off.
From: P.O.A
Features 16 relays configured for balanced stereo audio and will switch 8 stereo inputs to one stereo output or, as the switching is done by relays, it could be one stereo input to 8 stereo outputs.
From: P.O.A
This card features 16 relays configured for balanced audio in the 7.1 surround-sound format. Operates off a supply voltage of between +5V and +15V.
From: P.O.A
This card takes up to 8 x VS1192 Single Quad VCA cards and is ideally suited to level control of surround sound systems. Can be supplied with or without VCA cards pre-fitted.
From: P.O.A
Miscellaneous
Rack-mounted channel solid-state VCA-based compressor / limiters that can operate as individual channels, stereo or multichannel by linking several units together. The 1107 is a broadcast compressor with transformer-coupled inputs and outputs. The 1149 is a precision compressor with electronic-coupled inputs and outputs.
From: P.O.A
The 1156 Twin Viper Card Frame houses up to two Telecast Viper II modules in a convenient all aluminium 1U rack.
From: P.O.A
Two Calrec M Series PQ modules featuring mic and line balanced inputs with switchable phase reverse together with variable high and low pass filters plus 4 band parametric EQ in a 2U rack.
From: P.O.A
A test jig to make the servicing and repair of Neve VR EQ EV11491 modules that little bit easier.
From: £105.00
A versatile bench power supply unit for small audio applications and testing purposes providing: Audio, Logic and Phantom @ 1A. Suitable for powering Neve or Calrec modules.
From: £295.00
The unit, also known as the Channel in a Box or CIB for short, is based around the Inputs, Dynamics, EQ and Insert sub-assembly from a Neve VR channel. Two versions are currently available with optional transformer or electronic outputs. The vintage Neve V Series sound re-engineered with extras ... without compromise!
From: £665.00
A uniquely designed Trimodal Power Amplifier that is instantly switchable between Class A and Class B. There are no compromises of any kind in either mode. Available as a fully assembled and tested unit or in various kit options.
From: £27.50
After an extended period of development, improvement and extensive sourcing of the best possible components the STC003 Precision Preamplifier is not only back it is now probably the best preamplifier in the world. Available as a fully assembled and tested unit or in various kit forms.
From: £33.00
The STC004 Load-Invariant Power Amplifier has been redesigned to use the latest output transistors in either TO3P or MT-200 packages. Available as a fully assembled and tested unit or in various kit forms.
From: £33.00
The STC005 Class G Power Amplifier Module is particularly suitable for driving sub-woofers or the low-frequency units in multi-amped systems. Its performance is far superior to the Class-D amplifiers sometimes used for this task, giving lower noise, much lower distortion, and an efficiency with real signals that is almost as good. Available as a fully assembled and tested unit or in various kit options.
From: £33.00
A stand-alone version of the phono system used in the STC003 Precision Preamplifier. It offers both moving-magnet and moving-coil inputs, the latter with two gain options for optimal performance. Available as a fully assembled and tested unit or in various kit options.
From: £28.00
A stand-alone version of the phono system used in the STC003 Precision Preamplifier. It offers both moving-magnet and moving-coil inputs, the latter with two gain options for optimal performance. Available as a fully assembled and tested unit or in various kit options.
From: £32.00
The STC008 Amplifier Speaker Protection provides safety against excess DC-offsets, over-temperature conditions and turn-on/turn-off transients. Can be easily added to almost any amplifier system. Available as a fully assembled and tested unit or in various kit options.
From: £23.00
The STC009 Compact Blameless Power Amplifier Module is an economical and space-efficient Class-B amplifer that provides all the benefits of blameless performance. Intended for use with loads that are nominally 8Ω but will still give excellent performance into lower impedances. Available as a fully assembled and tested unit or in various kit options.
From: £23.00
The conventional balanced input stage built with 10K resistors and a 5532 op-amp has a far worse noise performance than a simple unbalanced input and is also much noisier than any of our power amplifier designs. The STC012 solves this problem by using a multiple amplifier array that causes the noise from each amplifier to partially cancel, and in a similar way improves the common-mode rejection ratio. Available as a fully assembled and tested unit or in various kit options.
From: £19.80
Provides a high-current power supply for powering two STC amplifiers, combined with regulated +/-17V supplies for powering op-amp circuitry such as the STC012 Low Noise Input Module (Balanced) or the STC008 Amplifier Speaker Protection Module. Available as a fully assembled and tested unit or in various kit options.
From: £27.50
Neve V3 and VR 64 way and 96 way compatible extender cards. Available in the following configurations: 64-way (2 row), 64-way (3 row) and 96-way (3 row). Sets are also available for the following consoles: V3 Set consisting of 4 x 64-way (3 row) and VR Set consisting of: 3 x 64-way (3 row) and 1 x 96-way (3 row).
From: £69.95
Modular Assemblies
A 6 channel fader panel featuring either ALPS K series or P&G 3000 faders and a buffer amp card for the Neve V.Mini-Master Sidecar systems.
From: £657.00
A channel meter panel featuring 12 large illuminated VU Meters with their respective SIG and DYN LEDs for 12 / 24 channel Neve V.Mini-Master Sidecar systems.
From: P.O.A
A slave meter bridge panel featuring 12 circular VU Meters for 12 / 24 channel Neve V.Mini-Master Sidecar systems. Available with both SIG and DYN LEDs or with SIG LEDs only.
From: P.O.A
A main mix and meter panel featuring 6 large illuminated VU meters and a phase meter for 12 / 24 channel Neve V.Mini-Master Sidecar systems.
From: P.O.A
The V.Mini-Master Control Panel provides all the necessary features of a Neve V.Mini-Master Sidecar master section (together with additional functions for headphone and control room monitors), in a clear and concise panel.
From: £4,457.00
A high quality, silent, convection-cooled 5U power supply unit for a 12 channel Neve V.Mini-Master Sidecar system.
From: £3,494.00
A versatile bench power supply unit for small audio applications and testing purposes providing: Audio, Logic and Phantom @ 1A. Suitable for powering Neve or Calrec modules.
From: £295.00
Neve V.Mini-Master Sidecar
The Neve V.Mini-Master Sidecar affords all the functionality of a full size Neve V Series Console in a compact footprint. Available as a complete unit or in kit form tailored to individual needs.
From: P.O.A
The V.Mini-Master Control Panel provides all the necessary features of a Neve V.Mini-Master Sidecar master section (together with additional functions for headphone and control room monitors), in a clear and concise panel.
From: £4,457.00
A high quality, silent, convection-cooled 5U power supply unit for a 12 channel Neve V.Mini-Master Sidecar system.
From: £3,494.00
A channel meter panel featuring 12 large illuminated VU Meters with their respective SIG and DYN LEDs for 12 / 24 channel Neve V.Mini-Master Sidecar systems.
From: P.O.A
A slave meter bridge panel featuring 12 circular VU Meters for 12 / 24 channel Neve V.Mini-Master Sidecar systems. Available with both SIG and DYN LEDs or with SIG LEDs only.
From: P.O.A
A main mix and meter panel featuring 6 large illuminated VU meters and a phase meter for 12 / 24 channel Neve V.Mini-Master Sidecar systems.
From: P.O.A
The JN1385 Neve V.Mini-Master Sidecar Monitor and Master Fader Panel is specifically designed for multi-bucket Neve V.Mini-Master Sidecar systems and features expanded Talkback, Monitor and Main Fader facilities.
From: P.O.A
A 6 channel fader panel featuring either ALPS K series or P&G 3000 faders and a buffer amp card for the Neve V.Mini-Master Sidecar systems.
From: £657.00
An optional 2U rack mounted XLR interface panel providing Monitor / Line inputs for the Neve V.Mini-Master Sidecar systems.
From: £554.00
An optional 2U rack mounted XLR interface panel providing Group and Multitrack Send inputs for the Neve V.Mini-Master Sidecar systems.
From: £322.00
An optional 1U rack mounted XLR interface panel providing Mic inputs for the Neve V.Mini-Master Sidecar systems.
From: £417.00
An optional 2U rack mounted XLR interface panel providing Insert Send / Return inputs for the Neve V.Mini-Master Sidecar systems.
From: £322.00
An optional 2U rack mounted XLR interface panel providing Group Out / Key inputs for the Neve V.Mini-Master Sidecar systems.
From: £322.00
An optional 2U rack mounted XLR interface panel providing Main, Mix Insert and Aux outputs for the Neve V.Mini-Master Sidecar systems.
From: £311.00
An optional 2U rack mounted XLR interface panel providing Main and Monitor outputs for the Neve V.Mini-Master Sidecar systems.
From: £299.00
Provides 8 Aux busses, 2 stereo busses and AFL/PFL busses for the NM1249 V.Mini-Master Sidecar Control Panel. Two versions are available for the Neve V1 / V2 / V3 and VR / VL / VX series consoles respectively.
From: £120.00
Provides connections to the NM1249 V.Mini-Master Sidecar Control Panel on an EDAC connector.
From: P.O.A
Power Supply Units
A high quality, silent, convection-cooled 5U power supply unit for a 12 channel Neve V.Mini-Master Sidecar system.
From: £3,494.00
A versatile bench power supply unit for small audio applications and testing purposes providing: Audio, Logic and Phantom @ 1A. Suitable for powering Neve or Calrec modules.
From: £295.00
Rack Units
Rack-mounted channel solid-state VCA-based compressor / limiters that can operate as individual channels, stereo or multichannel by linking several units together. The 1107 is a broadcast compressor with transformer-coupled inputs and outputs. The 1149 is a precision compressor with electronic-coupled inputs and outputs.
From: P.O.A
The 1156 Twin Viper Card Frame houses up to two Telecast Viper II modules in a convenient all aluminium 1U rack.
From: P.O.A
Two Calrec M Series PQ modules featuring mic and line balanced inputs with switchable phase reverse together with variable high and low pass filters plus 4 band parametric EQ in a 2U rack.
From: P.O.A
A high quality, silent, convection-cooled 5U power supply unit for a 12 channel Neve V.Mini-Master Sidecar system.
From: £3,494.00
The unit, also known as the Channel in a Box or CIB for short, is based around the Inputs, Dynamics, EQ and Insert sub-assembly from a Neve VR channel. Two versions are currently available with optional transformer or electronic outputs. The vintage Neve V Series sound re-engineered with extras ... without compromise!
From: £665.00
An optional 2U rack mounted XLR interface panel providing Main, Mix Insert and Aux outputs for the Neve V.Mini-Master Sidecar systems.
From: £311.00
An optional 2U rack mounted XLR interface panel providing Main and Monitor outputs for the Neve V.Mini-Master Sidecar systems.
From: £299.00
An optional 1U rack mounted XLR interface panel providing Mic inputs for the Neve V.Mini-Master Sidecar systems.
From: £417.00
An optional 2U rack mounted XLR interface panel providing Group and Multitrack Send inputs for the Neve V.Mini-Master Sidecar systems.
From: £322.00
An optional 2U rack mounted XLR interface panel providing Insert Send / Return inputs for the Neve V.Mini-Master Sidecar systems.
From: £322.00
An optional 2U rack mounted XLR interface panel providing Monitor / Line inputs for the Neve V.Mini-Master Sidecar systems.
From: £554.00
An optional 2U rack mounted XLR interface panel providing Group Out / Key inputs for the Neve V.Mini-Master Sidecar systems.
From: £322.00
Sub Assemblies
A compact single-channel card using the NE5534 op-amp. Available as a fully assembled and tested unit or in kit form.
From: £20.00
A Compact stereo power amplifier based on the LM1875. Power output is up to 20 watts per channel. The achievable power output depends on the heatsink to which the BS1118 (LM1875) Compact Stereo Power Amplifier is fixed and the power supply voltage used.
From: P.O.A
This discrete stereo headphone amplifier is a very high-quality circuit that will run on a DC supply between +/-12V and +/-30V. Ideal for studio foldback systems, DJ headphone amplifiers and enhanced console headphone outputs.
From: P.O.A
A pair of circular cards that fit on the back of the respective meter type: VU or PPM. The design allows for the meter and its driver to be fitted through the circular mounting hole. The drivers are supplied tested and aligned, however fine-alignment is recommended.
From: P.O.A
A new, improved and longer lasting LED assembly to replace the original LED assembly in the Neve VR / VL / VX Series aux meters. Available in either yellow or white illumination.
From: £34.95
The Neve 51 Series Direct Output Card has one of two balanced inputs (can be configured as unbalanced), selected by an illuminated switch. A level control sets the level at the balanced output. Although designed for the 51 Series consoles, this card can be used in any application where one of two signals needs to be selected.
From: P.O.A
A Compact 2-channel card featuring a pair of cross-coupled balanced outputs each using NE5532 dual op-amps. The classic configuration of balanced output used in many consoles and pro-audio products in a convenient package.
From: £30.00
A compact 2-channel card using the high-performance INA2137 line receiver. Featuring: +4dBu in, -2dBu out.
From: £25.00
A compact 2-channel input card using the NE5532 op-amp. Featuring: +4dBu in, -2dBu out. The card has a gain of +6dB.
From: £25.00
A compact 2-channel output card using SSM2142 drivers. Featuring: -2dBu in, +4dBu out.
From: £30.00
A single-channel output driver card using a unique servo circuit. The card has output level trim, as well as common-mode trims for HF and LF.
From: £40.00
A single-channel output driver card using a cross-coupled output driver. The card has output level trim, as well as an output balanced trim.
From: £35.00
A Single-channel cross-coupled card using the NE5532 op-amp. Featuring: -2dBu in, +4dBu out.
From: £25.00
A single-channel high performance card using the Lundahl LL1517. Featuring: -2dBu in, +4dBu out.
From: £95.00
A single-channel card using the NE5532 op-amp. Featuring: -2dBu in, +4dBu out.
From: £25.00
A compact 2-channel mix amp with differential outputs. Uses the TLE2027 high-performance op-amp for mix stage. Requires 10k mix resistors to feed the card.
From: £30.00
A single-channel high-quality mix amp card with +/-1.5dB output gain trim. Non-inverting through-path. Requires 10k mix resistors to feed the card.
From: £25.00
A LED phase meter assembly designed to fit in the top of a Sifam type 74 twin-needle PPM. The assembly includes LED illumination for the twin needles.
From: P.O.A
A smoothing cap card for use in console power supply units and similar. Featuring: 2 rows of 4 snap-in electrolytic caps, typically 10,000uF 50V each.
From: £75.00
A compact rectifier and snubber-cap card for use with the PF1289 PSU Smoothing Cap Card and PS1290 15A PSU Bipolar Regulator card.
From: £15.00
A compact 1.5A Bipolar Regulator card with logic supply up to 3A and a +48V supply at 0.75A. Mounting to a heatsink or equipment chassis for heat dissipation is essential for supplying the full current.
From: P.O.A
Bipolar power supply for audio: +/-17V at up to 3A on a compact card. The positive and negative rails track to within 0.6V. Mounting to a heatsink or equipment chassis for heat dissipation is essential for supplying the full current.
From: P.O.A
This 15A Bipolar Regulator card is designed for high-quality console power supply systems. Comprises of 2 regulator sets each capable of an absolute maximum of 15A dependent on heatsinking and thermal performance of enclosure.
From: £225.00
The card comprises of 2 independent 4-into-1 analogue switches. Can be used as 2 x mono routers, 1 stereo router, 1 differential router or, an 8 into 1 router. Any number of inputs can be active.
From: £12.50
The RS1123 CMOS Analogue Routing Card comprises of 2 independent inputs each routing to 4 outputs. Can be used as 2 x mono routers, 1 stereo router, 1 differential router or a 1 into 8 router. Any number of inputs can be active.
From: £12.50
An analogue routing card with 6 stereo (or balanced) inputs and a stereo (or balanced) output. Any number of inputs can be active.
From: £12.15
A complete soft-logic replacement assembly for Neve V Series 16 button monitor switch banks. The switches control gold contact relays and the wiring is soldered on to a pcb which allows for disconnection should the logic board require servicing.
From: £645.00
A general purpose card featuring 4 x TQ2 double-pole relays. Each relay has its own enable input and LED output to indicate that the relay is on. All relay contacts are available separately for maximum flexibility. NB. LEDs are not supplied.
From: £20.00
This assembly is designed as an add-in for Neve 51 Series modules with no direct output, Neve 51 series modules that require a direct output earlier in the module audio path or, as a replacement to the high voltage output drive transistor circuit used on the direct outputs / inserts / master outputs. Various options available.
From: £11.95
A very high quality single-channel VCA card featuring a balanced input and differential output. Noise and distortion is reduced significantly by the use of paralleled VCAs. Level and distortion trim controls are provided.
From: P.O.A
This card allows up to 6 momentary switches to be configured as an interlocking switch bank where only 1 of 6 is active at any time. Designed to directly interface with the with the RS1215 CMOS Analogue Routing Card (12 Inputs / 2 Outputs) the RS1122 CMOS Analogue Routing Card (4 Inputs / 1 Output) and the RS1123 CMOS Analogue Routing Card (2 Inputs / 8 Outputs).
From: £30.00
This card has 5 electronic latches that are controlled by a contact-closure (either a mechanical switch or a low-resistance path such as a FET or CMOS analogue gate). Typically used in conjunction with the RS1215 CMOS Analogue Routing Card (12 Inputs / 2 Outputs) the RS1122 CMOS Analogue Routing Card (4 Inputs / 1 Output) and the RS1123 CMOS Analogue Routing Card (2 Inputs / 8 Outputs).
From: £30.00
Support Cards
A breakout PCB for the Calrec M Series PQ1253 Microphone Equaliser Module - or similar. Features a 16-way IDC power connector for easy joining together of several cards using ribbon cable.
From: £30.00
A new, improved and longer lasting LED assembly to replace the original LED assembly in the Neve VR / VL / VX Series aux meters. Available in either yellow or white illumination.
From: £34.95
The Neve 51 Series Direct Output Card has one of two balanced inputs (can be configured as unbalanced), selected by an illuminated switch. A level control sets the level at the balanced output. Although designed for the 51 Series consoles, this card can be used in any application where one of two signals needs to be selected.
From: P.O.A
A complete soft-logic replacement assembly for Neve V Series 16 button monitor switch banks. The switches control gold contact relays and the wiring is soldered on to a pcb which allows for disconnection should the logic board require servicing.
From: £645.00
This card pair adapts the LK1103 Neve VR 8-Way Aux Line Level Converter directly to a pair of EDAC connectors that are tracked to the Neve pin-out.
From: P.O.A
A PCB designed to accept either 64 a/b, 64 a/c or 96 a/b/c DIN41612 type connectors. Ideal to allow for bench connection to channel modules using the DIN41612 type connectors to mate to console channel bucket backplanes.
From: £9.95
Cables
Interface Cables
Replacement recall fibre optic cable for Neve V Series consoles - available in increments of 5 metres up to a maximum of 20 metres.
From: £120.00
Replacement VGA Cable (M-F) - available in increments of 5 metres up to a maximum of 20 metres.
From: £32.64
Replacement Mouse / Trackball / Pointer Cable - all lengths are catered for up to a maximum of 20 metres and supplied in increments of 5 metres.
From: £91.00
Replacement Recall (D25M-D25M) cable for Neve V Series consoles. All lengths are catered for up to a maximum of 20 metres and supplied in increments of 5 metres.
From: £341.00
Replacement Keyboard cable - available in increments of 5 metres up to a maximum of 20 metres.
From: £83.00
Power Cables
Replacement Neve console power cables - available in increments of 5 metres up to a maximum of 20 metres.
From: £895.00
Replacement high voltage PSU cable for Neve V Series consoles plasma meters - available in increments of 5 metres up to a maximum of 20 metres.
From: £174.00
Replacement Neve V Series flying fader PSU cable - available in increments of 5 metres up to a maximum of 20 metres.
From: £385.00
Replacement dynamic meter power cable for Neve V Series consoles. Power supply cables used on the Neve range of consoles are all built to order. As such, the various cable lengths supplied originally may not necessarily translate to a second install.
From: £295.00
Parts
Components
We supply both standard capacitor kits and custom kits for particular customers, consoles or module types. All kit types include instructions stipulating which capacitor types are fitted where on each PCB.
From: P.O.A
A PSU regulator recapping kit for Neve V3 and VR consoles. All kits include instructions stipulating which capacitor types are fitted where on each PCB. See also: CAPKIT002 Neve 51 / V1 PSU Regulator Recap Kit.
From: £39.95
A PSU regulator recapping kit for Neve 51 and V1 consoles. All kits include instructions stipulating which capacitor types are fitted where on each PCB. See also: CAPKIT001 Neve V3 / VR PSU Regulator Recap Kit.
From: £57.95
Cosmetics
We stock a range of cosmetic items suitable for all ages and ranges of Neve consoles.
From: P.O.A
This card allows high quality buffering of balanced signals whilst cutting or boosting the level of each signal.
From: P.O.A
A complete soft-logic replacement assembly for Neve V Series 16 button monitor switch banks. The switches control gold contact relays and the wiring is soldered on to a pcb which allows for disconnection should the logic board require servicing.
From: £645.00
This assembly is designed as an add-in for Neve 51 Series modules with no direct output, Neve 51 series modules that require a direct output earlier in the module audio path or, as a replacement to the high voltage output drive transistor circuit used on the direct outputs / inserts / master outputs. Various options available.
From: £11.95
CUT, SOLO and OD switches - designed to replace the original ITW Licon switch unit as used by Neve and AMS Neve on the V Series console channel modules.
From: £10.35
Kits
A compact single-channel card using the NE5534 op-amp. Available as a fully assembled and tested unit or in kit form.
From: £20.00
A PSU regulator recapping kit for Neve V3 and VR consoles. All kits include instructions stipulating which capacitor types are fitted where on each PCB. See also: CAPKIT002 Neve 51 / V1 PSU Regulator Recap Kit.
From: £39.95
A PSU regulator recapping kit for Neve 51 and V1 consoles. All kits include instructions stipulating which capacitor types are fitted where on each PCB. See also: CAPKIT001 Neve V3 / VR PSU Regulator Recap Kit.
From: £57.95
A pair of circular cards that fit on the back of the respective meter type: VU or PPM. The design allows for the meter and its driver to be fitted through the circular mounting hole. The drivers are supplied tested and aligned, however fine-alignment is recommended.
From: P.O.A
The Neve 51 Series Direct Output Card has one of two balanced inputs (can be configured as unbalanced), selected by an illuminated switch. A level control sets the level at the balanced output. Although designed for the 51 Series consoles, this card can be used in any application where one of two signals needs to be selected.
From: P.O.A
A LED phase meter assembly designed to fit in the top of a Sifam type 74 twin-needle PPM. The assembly includes LED illumination for the twin needles.
From: P.O.A
A smoothing cap card for use in console power supply units and similar. Featuring: 2 rows of 4 snap-in electrolytic caps, typically 10,000uF 50V each.
From: £75.00
A compact rectifier and snubber-cap card for use with the PF1289 PSU Smoothing Cap Card and PS1290 15A PSU Bipolar Regulator card.
From: £15.00
A compact 1.5A Bipolar Regulator card with logic supply up to 3A and a +48V supply at 0.75A. Mounting to a heatsink or equipment chassis for heat dissipation is essential for supplying the full current.
From: P.O.A
Bipolar power supply for audio: +/-17V at up to 3A on a compact card. The positive and negative rails track to within 0.6V. Mounting to a heatsink or equipment chassis for heat dissipation is essential for supplying the full current.
From: P.O.A
A versatile bench power supply unit for small audio applications and testing purposes providing: Audio, Logic and Phantom @ 1A. Suitable for powering Neve or Calrec modules.
From: £295.00
The card comprises of 2 independent 4-into-1 analogue switches. Can be used as 2 x mono routers, 1 stereo router, 1 differential router or, an 8 into 1 router. Any number of inputs can be active.
From: £12.50
The RS1123 CMOS Analogue Routing Card comprises of 2 independent inputs each routing to 4 outputs. Can be used as 2 x mono routers, 1 stereo router, 1 differential router or a 1 into 8 router. Any number of inputs can be active.
From: £12.50
An analogue routing card with 6 stereo (or balanced) inputs and a stereo (or balanced) output. Any number of inputs can be active.
From: £12.15
A complete soft-logic replacement assembly for Neve V Series 16 button monitor switch banks. The switches control gold contact relays and the wiring is soldered on to a pcb which allows for disconnection should the logic board require servicing.
From: £645.00
A uniquely designed Trimodal Power Amplifier that is instantly switchable between Class A and Class B. There are no compromises of any kind in either mode. Available as a fully assembled and tested unit or in various kit options.
From: £27.50
After an extended period of development, improvement and extensive sourcing of the best possible components the STC003 Precision Preamplifier is not only back it is now probably the best preamplifier in the world. Available as a fully assembled and tested unit or in various kit forms.
From: £33.00
The STC004 Load-Invariant Power Amplifier has been redesigned to use the latest output transistors in either TO3P or MT-200 packages. Available as a fully assembled and tested unit or in various kit forms.
From: £33.00
The STC005 Class G Power Amplifier Module is particularly suitable for driving sub-woofers or the low-frequency units in multi-amped systems. Its performance is far superior to the Class-D amplifiers sometimes used for this task, giving lower noise, much lower distortion, and an efficiency with real signals that is almost as good. Available as a fully assembled and tested unit or in various kit options.
From: £33.00
A stand-alone version of the phono system used in the STC003 Precision Preamplifier. It offers both moving-magnet and moving-coil inputs, the latter with two gain options for optimal performance. Available as a fully assembled and tested unit or in various kit options.
From: £28.00
A stand-alone version of the phono system used in the STC003 Precision Preamplifier. It offers both moving-magnet and moving-coil inputs, the latter with two gain options for optimal performance. Available as a fully assembled and tested unit or in various kit options.
From: £32.00
The STC008 Amplifier Speaker Protection provides safety against excess DC-offsets, over-temperature conditions and turn-on/turn-off transients. Can be easily added to almost any amplifier system. Available as a fully assembled and tested unit or in various kit options.
From: £23.00
The STC009 Compact Blameless Power Amplifier Module is an economical and space-efficient Class-B amplifer that provides all the benefits of blameless performance. Intended for use with loads that are nominally 8Ω but will still give excellent performance into lower impedances. Available as a fully assembled and tested unit or in various kit options.
From: £23.00
The conventional balanced input stage built with 10K resistors and a 5532 op-amp has a far worse noise performance than a simple unbalanced input and is also much noisier than any of our power amplifier designs. The STC012 solves this problem by using a multiple amplifier array that causes the noise from each amplifier to partially cancel, and in a similar way improves the common-mode rejection ratio. Available as a fully assembled and tested unit or in various kit options.
From: £19.80
Provides a high-current power supply for powering two STC amplifiers, combined with regulated +/-17V supplies for powering op-amp circuitry such as the STC012 Low Noise Input Module (Balanced) or the STC008 Amplifier Speaker Protection Module. Available as a fully assembled and tested unit or in various kit options.
From: £27.50